X-TOOLはドリル穴の入口、出口、プライマリ穴の横穴開口部の面取り・バリ取りを、ワンパスで完了することが出来る工具です。 X-TOOL is a tool that can complete chamfering and deburring of entrances and exits of drilled holes, and side hole openings of primary holes in one pass.
平板に直角にあいている穴の出入り口だけでなく、プライマリ穴にあけられた横穴(*1,*2)、斜めにあけられた穴(*3)などの面取りも可能です。
*1:セカンダリ側、プライマリ側のいずれからも加工が可能です。
*2:プライマリ側から面取りする横穴径はΦ0.5mm以上になります。
*3:穴の傾斜角は10°程度までが対象になります。
It is possible to chamfer not only entrances and exits of holes that are perpendicular to the flat plate, but also side holes (*1, *2)
drilled in the primary hole and oblique holes (*3).
*1: Machining is possible from either the secondary side or the primary side.
*2: The horizontal hole diameter to be chamfered from the primary side is Φ0.5mm or more.
*3: Up to 10° tilt angle of the hole is applicable.
面取りをする穴のサイズ、位置、個数など、さまざまなご要望に対応ができるように、X-TOOLには標準品とオーダーメイドタイプがあります。
標準品で対応できないものは、オーダーメイドとして検討いたしますので、まずはご相談ください。
X-TOOL has standard products and made-to-order types so that we can respond to various requests such as the size, position and number of holes to be chamfered.For items that cannot be handled with standard products,
we will consider making them as made-to-order, so please contact us first.
X-TOOLは本体を含めて4つの部品で構成しており、ばねがチップを常に押し出している状態になる構造となっています。
チップの交換はキャップをマイナスドライバーで外すだけで出来るので、簡単・確実・短時間で行なうことが可能です。
The X-TOOL consists of four parts, including the main body, and has a structure in which the spring constantly pushes the tip.
Tip replacement can be done simply by removing the cap with a flathead screwdriver, so it can be done easily, reliably, and in a short time.
穴の内壁に接触するチップ頂上部はR形状に処理をした切れ刃のないガイド面になっており、内径にキズをつけにくい形状になっています。
切れ刃の角度は90°を標準としていますが、オプションで変更も可能です。
チップのタイプは2種類あり、平板にあけられた穴の入口・出口の面取りには片刃タイプを、プライマリ穴にあけられた横穴の面取りには両刃タイプを使用します。
The apex of the tip that contacts the inner wall of the hole has a guide surface with no cutting edge processed into an R shape, making it difficult to scratch the inner diameter.
The standard cutting edge angle is 90°, but it can be changed as an option.
There are two types of tip, a single-edged type for chamfering the entrance and exit of holes drilled in a flat plate, and a double-edged type for chamfering horizontal holes drilled in the primary hole.
ドリル穴とX-TOOLを同芯にして正回転させながら挿入します。バネで押さえらているチップが入口のエッジに接触すると面取りを行いながら中心方向に押し込まれ、チップがドリル穴に入るまで送り面取りが完了します。
出口側は、チップが抜けた状態から同様にして引き抜くことで面取りを行ないます。
Insert the drill hole and X-TOOL concentrically while rotating forward.
When the tip pressed by the spring touches the edge of the entrance, It is pushed toward the center while chamfering, and the feed chamfering is completed until the tip enters the drill hole.
The exit side is chamfered by pulling out the tip in the same way.
X-TOOLのチップには片刃と両刃の2種類があるため、使用するチップによって加工方法が異なります。
これは加工箇所により変わります。
There are two types of X-TOOL tips: single-edged and double-edged, so the machining method differs depending on the tip used.
This varies depending on the processing location.