イレギュラーな開口形状であっても専用カッターで面取りが可能です。多種多様な開口形状に対応するため、専用設計した面取りカッターを使用します。 Even irregular opening shapes can be chamfered with a special cutter. A specially designed chamfering cutter is used to support a wide variety of opening shapes.
プライマリ穴とセカンダリ穴の交差が直角交差の他に、ななめ、ミゾ奥、同径同軸直交、異径同軸直交、出口一部R、平行オフセット、段差、異径直交オフセットなど、さまざまな開口形状の面取りが対象となります。 In addition to right-angle intersections of primary and secondary holes, Diagonal, depth of groove, same diameter coaxial orthogonal, Different diameter coaxial orthogonal, exit part R, parallel offset, step, Different diameter orthogonal offset etc, chamfering for various opening geometries is covered.
穴の内壁に接触するチップ頂上部はR形状に処理をした切れ刃のないガイド面になっており、内径にキズをつけにくい形状になっています。
全長・刃長・形状などの工具諸元は、加工対象の形状に合わせて決定します。
The top of the tip that comes in contact with the inner wall of the hole has an R-shaped guide surface without a cutting edge, making it difficult to scratch the inner diameter.
Tool specifications such as overall length, flute length, and shape are determined according to the shape of the object to be machined.
NXホルダに面取りカッターを取り付けると中心からオフセットした状態になるように、取り付け穴は中心からオフセットしたところにあります。
さらに、面取りカッターを取り付ける部分そのものが中心から外側に向かい、常にバネで押されている状態となっています。
加工時に面取りカッターに外側から力が加わると、面取りカッターはホルダの軸方向に動き、その力が無くなると、元の位置へ戻ります。
The mounting holes are offset from center so that when the chamfer cutter is installed in the NX holder it will be offset from center.
Furthermore, the part where the chamfering cutter is attached faces outward from the center and is always pressed by a spring.
When a force is applied to the chamfering cutter from the outside during processing, the chamfering cutter moves in the axial direction of the holder, and returns to its original position when the force is removed.
工具を回転させながら挿入していきます(Fig.1)。
入口で面取りカッターが接触すると、バネで押し付けられているカッターが面取りを行ないながら穴の中心方向へ移動していきます(Fig.2)。
横穴の開口部へ移動してくると、内径に接触していた面取りカッターが飛び出してきて、面取りを行います(Fig.3)。
Insert the tool while rotating it (Fig.1).
When the chamfering cutter comes into contact with the entrance, the cutter pressed by the spring moves toward the center of the hole while chamfering (Fig.2).
When it moves to the opening of the horizontal hole, the chamfering cutter that was in contact with the inner diameter jumps out and chamfers (Fig.3).
平板にあけられた穴のような直角交差の単純な形状の開口部の面取りであれば、正転用1本のみを使用することで完了します。
しかし、プライマリ穴からおこなうセカンダリ穴の面取りや、楕円などのイレギュラーな形状の開口部の面取りを行なうと、カッターの刃先が当たる前に逃げ面が開口部と干渉してしまう箇所が発生してしまいます。
このような時は、正転・逆転の2本を1セットとして面取り加工を行なう必要があります。
Chamfering of a simple rectangular opening such as a hole in a flat plate can be completed with a single forward turning tool.
However, when chamfering a secondary hole from a primary hole or chamfering an opening with an irregular shape such as an ellipse, there will be places where the flank interferes with the opening before it hits the cutter edge.
In such a case, it is necessary to perform chamfering with two sets of forward rotation and reverse rotation as one set.
面取りカッターのNXホルダへの取付けは、To attach the chamfering cutter to the NX holder,